-
Content count
308 -
Joined
-
Last visited
Everything posted by Av8r_Sed
-
Av8r_Sed added a post in a topic Airventure 2015
Thanks for sharing all of that, Doug. The Basler pics are fascinating. Maybe Larry should have had them do his wiring harness. What an operation!
-
0
-
-
Av8r_Sed added a post in a topic setting the wings
Larry, PM sent.
You may not be able to get it perfect with the flaperons even when folded. Mine are off just a bit. It's more important to have it rigged right for flying. It takes a little fiddling, but you should be able to arrive at a good compromise.
-
0
-
-
Av8r_Sed added a post in a topic solving poor power / performance issues
Minimum water temp for flight on a 582 per the Rotax Operator's manual is listed as 150 F. 115 is too low and I suspect your reading is way off. What kind of gauge are you using? The Westach quad gauges are notoriously innacurate, though more often with the EGT's. I had a Rotax water temp sensor go bad on me too. You could pull the sensor and calibrate against a thermometer in a hot water bath to see if you're in the ballpark or not.
If your temps really are that low, bad things could happen such as cold seizure, leading to piston scuffing.
-
0
-
-
Av8r_Sed added a post in a topic MTOW mod question
There was a post on the other site with one approach: http://www.teamkitfox.com/Forums/showthread.php?t=6110
The size of the lift struts is a key component along with the carry through.
-
0
-
-
Av8r_Sed added a post in a topic Seat Belt and Seat Pan Routing (Kitfox III)
Ed, my III came with 4 point Hooker belts which hold me in nice and snug.
Larry, if anyone else doesn't come up with a pic, I'll post one this week after I get out to my hangar.
-
0
-
-
Av8r_Sed added a post in a topic Crossed the US in My Avid Flyer Mk IV
Good job, Nick! ...and all on 582 power. Thanks for the pics and commentary. You make it look easy.
-
0
-
-
Av8r_Sed added a post in a topic It Flies After 9 years
The Hacman style is very effective and simple once it's installed. I haven't had any issues with mine.
Is the Artic Sparrow system still available?
-
0
-
-
Av8r_Sed added a post in a topic It Flies After 9 years
Good to hear you've saved another of our birds from oblivion. Good Job!
Keep the Hacman system in mind if managing the EGT's ends up giving you the blues. It's great just dialing in the EGT you want and not worrying about rejetting for changing conditions.
-
0
-
-
Av8r_Sed added a post in a topic Muffler insulation
Jon,
I had my 582 exhaust ceramic coated. It ends up with a silvery metallic finish. Though I don't have before/ after data, it does seem to move more heat out of the cowling. It makes sense since nothing radiates heat better than a flat black surface (in this case inside the cowling).
-
0
-
-
Av8r_Sed added a post in a topic Overhaul time!
I believe the firewall material is a form of Fiberfrax blanket, though I haven't found a source for the quilted type. I have the same on my Model III. It's a non-asbestos ceramic insulation.
-- Sed
-
0
-
-
Av8r_Sed added a post in a topic Classic IV Restoration
Very sharp! Those colors really pop. You're sure trucking along.
-
0
-
-
Av8r_Sed added a post in a topic Flushing wing tanks and adding sight tubes
Density of gasoline is about 0.7 gm/cc. Buna-N rubber is 1.2 to 1.3. The balls will sink.
-
0
-
-
Av8r_Sed added a post in a topic 5 yr olds first off airport adventure
What a cutie! She's lucky to have a papa pilot to take her on big adventures.
-
0
-
-
Av8r_Sed added a post in a topic Cable operated enrichers (choke) 582
I run the enrichers on my 582. Came with the kit as well as a primer. I decided I didn't want the tygon fuel tubing in the cockpit and the enrichers seem to work fine for me.
-
0
-
-
Av8r_Sed added a post in a topic Classic IV Restoration
Keep motoring Larry! You're making great progress. The fabric and panel are looking great. Def going to fly this year if you keep it up.
-
0
-
-
Av8r_Sed added a post in a topic belly radiator
I thought minimum for T/O was 150 on a 582. He must not have installed a thermostat.
Mine is currently tucked up against the belly. It gets up to 180 on a climb and usually settles to around 170.
-
0
-
-
Av8r_Sed added a post in a topic Lexan/plexi protective sticky paper removal
I tried heat, Goo Gone and mineral spirits. None made it easy. In the end, my stubborn determination got it off, but I probably would have been better served buying a new piece.
-
1
-
-
Av8r_Sed added a post in a topic Prop shaft seals
I used an inexpensive one with good results.
-
1
-
-
Av8r_Sed added a post in a topic Rib Stitching Vertical (leading edge down trailing edge up)
A very similar rotisserie design: http://tropicaltuba.com/Kitfox%20Project/Kitfox.htm#WingRotisserie
-
1
-
-
Av8r_Sed added a post in a topic Net Neutrality
Well, that's a bit of Fox sensationalism, Mr.
Here's a link to balanced coverage of what's going on with the FCC and Congress at the moment: http://www.politico.com//story/2015/02/reality-check-on-net-neutrality-rhetoric-115460.html
I for one, thinnk the monopolistic ISP's like Comcast and AT&T have too much power and don't represent consumerrs in the least. I'm a believer that they need to be treated like a utility just like my electricity or gas supplier.
-
0
-
-
Av8r_Sed added a topic in For Sale and wanted, you got it, I want it
KF III near MinneapolisI ran across a Craigslist ad for a 582 powered Kitfox Model III in Hudson, WI. I have no personal knowledge of this plane or the seller. Looks like it has a little recently repaired wingtip damage on one side.
http://minneapolis.craigslist.org/ws...886472915.html __________________- 6 replies
- 977 views
-
Av8r_Sed added a post in a topic Electrical experts
How about this one? Pretty similar, but easier mounting with the supplied nut and gasket. You have to be careful to get the correct sex on the pins for each half and make sure you get the solder cup version. Available from Digi-Key or Mouser.
http://www.mouser.com/Connectors/Circular-Connectors/Standard-Circular-Connectors/Standard-Circular-Connector/_/N-av49jZscv7?P=1z0x3z0&Keyword=mini-con-x&FS=True&Ns=Pricing|0
-
0
-
-
Av8r_Sed added a post in a topic Travis AFB iron from above and some warbird pics
Thanks for the nice pics, but you forgot to show where your hangar is located on the field. Must have been an oversight.
-
0
-
-
Av8r_Sed added a post in a topic Classic IV Restoration
Thanks for the link and filling in part of my education. I was surprised their online configurator had so many flavors of KF's and Avids. I like that you can get an idea on configuration and pricing after filling a couple of dropdown choices. Are they adding a Kitfox Rotax Zipper in your honor?
-
0
-
-
Av8r_Sed added a post in a topic Classic IV Restoration
Say what? More info please! Sounds like a custom surf board carver to me. Wood?
-
0
-